Friday, August 28, 2015

How to replace the starter in a 2.4L Hyundai Sonata

  The starter in a 2011 Hyundai Sonata is a challenge to replace owing to it's position high on the engine and obstructions blocking removal. This post will provide some helpful tips in removing and installing this starter.

                                                  The Job at a glance

  • Tools: 10,12 and 14mm sockets, 14mm deep well socket, 3/8" ratchet, floor jacks and supports, Philips screwdriver  
  • Parts and materials: starter
  • Cost of parts and materials: approx. $90-150 
  • Time: 2 hours 
  • Shop cost: $100- 150 or even much more

Removal


1) Disconnect the battery
2) Jack up the front end and put on supports. A good jack and support point are the rails running under both sides of vehicle.
3) From under the car remove the narrow front splash shield. Remove two 10mm  hex head screws on the ends and two Philips head panel fasteners in the middle of this piece and pull it out.
4) Remove the large under engine splash shield. This will come out in one large piece. There are seven 10mm hex fasteners. Four are on the front edge and three toward the rear. When all are removed, tug down on the front and pull the entire cover toward the front of the car. The starter is now visible above the oil filter. One of the two 14mm bolts is accessible from below and the other is best removed from above. It's under the air intake assembly. 



5) Remove the intake cover. It unsnaps from four bosses at the corners. 
6) Remove the air intake assembly. Loosen the hose clamp holding the air intake to the air intake plenum. Then unsnap the four air cleaner cover clamps. Remove a hose coming in to the left side of the assembly. Then the assembly can be lifted up and set out of the way. 


Air intake out of the way to expose starter bolts

7) Unbolt the starter. The top bolt can be removed from above and the lower from below or above.


The upper 14mm starter mounting bolt


The view of the lower starter mounting bolt from underneath

8) There are still obstructions to remove. Remove a 12mm bolt holding a bracket that holds the oil lines to the oil filter.
9) Loosen, but do not remove four 12mm bolts holding a black bracket that mounts the intake plenum to the engine. A 3/8" universal worked well for the engine bolts. A 12" extension worked to loosen the plenum bolts. 


Loosen, but don't remove these four 12mm fasteners

10) Ease the starter on down and rest it where the wiring can be removed. 
11) Unwire the starter. Unsnap the solenoid control wire connector. Remove the 12mm nut from the B+ wire. This connection is under a protective boot. 


Lift the boot and turn off the 12mm  B+ nut



12) Remove the starter from the car. 


Installation


1) Set the starter up in car and rest it on the oil pump hoses.
2) Wire the starter up. Wire the B+ up with the 12mm nut and seat the protective boot. Plug in the solenoid connection.
3) Move the starter into mounting position and turn in the lower bolt by hand while holding up the starter with the other hand. Turn it most of the way in but not torqued yet. Then start the top bolt and snug it up. Turn both to final torque. I don't worry about a torque wrench on starter bolts. Just cinch them up good. 
4) Mount that intake plenum bracket with the same 12mm tools.
5) Mount the oil filter hose bracket with the 12mm socket. 
6) Remount the air intake assembly on top.
7) Snap the intake cover back into place.
8) Remount the large lower splash shield with the seven 10mm bolts.
9) Mount the smaller from splash shield with the two 10mm bolts and the two panel fasteners. 
10) Lower the vehicle off the stands
11) Wire up the battery
12) Test the starter



                                 

17 comments:

  1. You always write fabulous. This is third time I am reading any of your blog and again finding it inspirational one. And I am sure this number is going to be increased. For more information visit this link:- Scrap Metal Recycling Sydney

    ReplyDelete
    Replies
    1. Thanks for the comment. You inspire me to keep them coming!

      Delete
  2. Nothing wrong if I say that you are really a wonderful writer. You always raise the social causes in your article which is respectful and admirable for me as an individual.Scrap metal Melbourne

    ReplyDelete
    Replies
    1. I appreciate that and thanks for having a look at the tutorial.

      Delete
  3. good job man good

    ReplyDelete
  4. just finished a starter change on a 2010 santa fe,2.4 eng. I followed every step you wrote, except I removed the bracket. had to, to get the new starter in. some aftermarket starters come with a longer body(a.k.a tyc brand)you are spot on in the time it took, two hours.thanks for the great post. a parts guy

    ReplyDelete
    Replies
    1. I really appreciate your reading my posts. Glad it helped you on your Sante Fe. I'll keep posting these for the good words from users like you!

      Delete
  5. Thank you so much for pics and information, I am trying to install remote start but i am not able to access push start button/Engine start stop button connector. I was able to take out side panel and lower panel but i cannot get my hand behind button. How I can take out Push to start/Engine start stop button PANEL. Thank you :)

    ReplyDelete
  6. All I can say is thank you. I had watched some youtube videos but it wasn't until I found this blog that I felt confident enough to take a shot at it. Thanks to your procedure and excellent pictures, I managed to pull it off and saved hundreds!

    ReplyDelete
    Replies
    1. You're very welcome. I'm so glad this blog helped you.

      Delete
  7. The Pittsburgh automotive floor jack comes with a rapid pump. This is what allows you to get to the maximum height with only 3.5 pumps. You will not need a lot of effort to be able to lift your load. Pittsburgh floor jack guide is a one of the best floor jack.

    ReplyDelete
  8. Thank you for this! It really helped when my dad and brother were changing out the starter in my Sonata. Very clear, detailed instructions and I love that you listed out what tools would be needed.

    ReplyDelete
  9. Thank you very much for the work you put on this post, just save me $200 people like you makes internet amazing, thank you.

    ReplyDelete
  10. Very good explanation. Easy to follow the steps. Thanks.

    ReplyDelete
  11. Thanks for sharing such a great information.It really helpful to me. I always search to read the quality content and finally i found this in you post. Plz keep it up!

    ReplyDelete
  12. I was eager to find this page. I needed to thank you for ones time for this especially awesome read!! I certainly truly preferred all aspects of it and I likewise have you book-set apart to look at new data in your blog.

    home insurance providers

    ReplyDelete
  13. Wish someone can help you in a complicated situation in the middle of the road, then Surrey Tow Truck is your best companion, we can help you by providing the best towing service in Surrey and other surrounding areas. We have a team of professionals equipped with trucks capable of towing buses, trucks, boats, and all types of heavy vehicles.

    ReplyDelete