Tuesday, April 11, 2017

How to replace the fuel filter and fuel pump 1996-2002 Caravan, Voyager or Town and Country

This post will cover some fuel system maintenance on a 1996 to 2002 Dodge Caravan, Plymouth Voyager and Chrysler Town and Country. These instructions cover both the fuel filter and fuel pump, but will be useful for either pump or filter replacement.

                                                The job at a glance

  • Tools:  Vice grip pliers, 10mm and 15mm wrench or socket and ratchet, strap wrench. Breaker bar may be needed. Also: Rags, pan to catch fuel 
  • Parts: Fuel filter, fuel pump 
  • Cost of parts: Filter $32; Fuel pump $58-$150 
  • Time: 2 hours    

Fuel system purge


This step is necessary to relieve the fuel pressure that exists throughout the system.

1) Remove the fuel pump relay. Locate it by removing the fuse and relay box cover in the engine compartment. The location is printed on the underside of the cover. Remove.



2) Attempt to start the van several times. When it fails to start and run the pressure is relieved.
3) Disconnect the negative of the battery.
4) Reinsert the relay. 

Fuel Filter removal


The fuel filter

1) Put the van on ramps or jack stands.
2) Place a jack and board under the fuel tank. The tank will need be lowered to access the pump and filter, which are atop the tank.
3) Remove the two 15mm strap bolts.



4) Lower the tank with the jack about 1 1/2 inches.
5) Disconnect the downstream fitting from the steel gas line. On this vehicle I had to squeeze the plastic insert while pulling back on the plastic fuel tubing of the filter assembly. A pliers such as a vice grip will help. Rust on the steel line under the insert made the job more challenging. I ended up cutting the tubing off longitudinally. 



6) Disconnect the two filter fittings from the fuel pump the same way. This is all plastic, so no corrosion to worry about. Have a catch pan ready for the inevitable fuel drip. 
7) Unbolt the filter canister from the mounting extrusion on the tank. This is 10mm bolt with a U-nut. Again, I encountered rust and had to cut the head off both the bolt and the nut. Make sure to take all precautions against sparks if this is needed. I sealed all gas lines, used a fan and had a fire extinguisher handy. 


I hope yours isn't this rusty!

8) Remove the old filter assembly. If not replacing the pump, move to fuel filter installation. If doing the pump continue...

Fuel Pump Removal

     I decided to replace the fuel pump as well at this time. The prep work is exactly the same as for the filter so this is an ideal time to knock off this job.


The fuel pump


1) Prep with steps 1-4 in fuel filter removal. 
2) Disconnect the two fuel lines from the pump by squeezing the plastic inserts and pulling the lines back. Have a pan ready to catch fuel.
3) Unplug the electrical connector. First release the locking tab with a dental pick or small screwdriver. Then move the tab to the right, and wiggle the connector free. 


This plug is tricky to unplug

4) Unscrew the lock ring atop the filter with a strap wrench. 


This strap wrench worked nicely

5) Clear off any dust or debris from the top of the pump and remove it. Angle it toward the front of the van and remove. It may have some gas inside so have the pan ready.


Fuel pump installation


1) If the new pump does not have the float attached, attach it using the original as a guide.
2) Slip the new o-ring on the pump
3) Install the pump. My aftermarket pump had an offset submersible filter that needed to be compressed on the way in. 
4) Turn on the lock ring. Make sure the o-ring is positioned properly. Align the protrusion on the pump with the notch in the tank while installing the ring. It won't turn in very far without using the strap wrench. Once the protrusion is seated in the notch, turn it on about as tightly as you can. 

Line up this protrusion with the notch in the ring on the tank

5) Plug in the electrical cable. The tab must be unlocked (moved to the right) going in and locked when seated.
6) Snap the two fuel lines into the pump. Put the color-coded inserts on the tank protrusions first. Turn them to align with the windows on the fittings on the end of the lines.  


Fuel Filter Installation

1) Mount the canister to tank with the 10mm nut. I used new hardware. 
2) Snap the two fuel lines into the pump. Put the color-coded inserts on the tank protrusions first. Turn them to align with the windows on the fittings on the end of the lines. 
3) Route the new downstream tubing part of the assembly under the front strap for the gas tank.
4) Snap the tubing into the steel gas line in the same manner as above.
5) Raise the tank but stop 1/4 from all the way up to allow some play to get the bolt started.
6) Start the 15mm strap bolts and then raise the tank the rest of the way. I put never-seize on the bolts.
7) Tighten the strap bolts.
8) Attach a ground strap from the filter to the front strap. 
9) Remove the jack.
9) Connect the battery and test for leaks. 

  
              

14 comments:

  1. Thanks for sharing such a wonderful instruction. As a vehicle owner, it is our duty to take care of our vehicle and do regular check-ups at every regular interval. But in the case of any big troubles like fuel filter change, engine problems, spark plug and battery problems, we need to consult expert advice. I would like to follow some essential instructions from this article regarding replacing a fuel filter.
    Smart Car Service NYC

    ReplyDelete
  2. This is a good read i have done today so far, I am delighted to came across it. I'll be back again to check out other posts as well. stainless steel castings

    ReplyDelete
  3. This comment has been removed by the author.

    ReplyDelete
  4. The workshop should be equipped with new appliances and computers. New models of communication allow you to order technical texts. This method has become popular in Europe and the USA. This company AU Edusson operates at the level of student and school education. Technical students use these assignment writers to write an essay.

    ReplyDelete
  5. In the event that you locate the foul stench of sewage at whatever point you circumvent the septic tank, at that point it has flooded, and your septic tank should be siphoned out right away. Warmtepomp

    ReplyDelete
  6. Since the dividers and underfloor zones were available, he could mount the units on inside dividers. Warmtepomp

    ReplyDelete
  7. There are two sorts of air conditioners that are fundamentally utilized in homes. Window style units are set in a window.Airco

    ReplyDelete

  8. A run of the mill ASHP is 300% proficient. This implies for each one kilowatt (kW) of power it utilizes, it will create 3kW of vitality. crompton solarium qube 15ltr

    ReplyDelete
  9. The organization was established in 1983 and from the earliest starting point has made these particular items the essential focal point of their activity. Warmtepompen

    ReplyDelete
  10. Sun based warm or sun powered high temp water gives up to 60% of your yearly heated water utilization. It requires a sun based warm gatherer to be introduced on your rooftop; lucht warmtepomp

    ReplyDelete
  11. Because of their short, straight forward establishment, this kind of heat siphon can be utilized with existing heating framework in your home just as for new form lodging. Warmtepomp

    ReplyDelete
  12. These machines are very useful but they are not cheap.instalação de ar condicionado

    ReplyDelete
  13. Moving parts needing grease can cause expanded electrical utilization and air conditioner repairs. Airco

    ReplyDelete